Technical Articles
Industrialization of the Composite 3D Printing for General Motors
- Posted: 02/06/2021 15:23:23
- Edited: 02/06/2021 15:34:33
- Clicks: 8
A few days ago, General Motors Corporation (GM) announced the opening of a 15,000 square feet Additive Industrialization Center (AIC) in the Warren Technology Center in the suburbs of Detroit....
Porsche and GM Have Obtained Achievement in 3D Printing Auto Parts Technology
- Posted: 01/07/2021 11:30:31
- Edited: 01/26/2021 16:31:48
- Clicks: 32
Porsche just announced that it would return to Le Mans with a surprising new prototype, and we can't wait to know its price. Although motorsport is a very important part of Porsche,...
Development of Aluminum Alloy Die Castings for Automobile Steering Knuckles (Part Two)
- Posted: 12/22/2020 15:30:35
- Edited: 12/22/2020 15:48:28
- Clicks: 20
4. Trial production results and analysis of steering knuckle castings 4.1 The influence of extrusion force on the internal quality of castings Figure 6 shows the non-destructive testing of steering knuckle...
Development of Aluminum Alloy Die Castings for Automobile Steering Knuckles (Part One)
- Posted: 11/20/2020 10:49:31
- Edited: 11/20/2020 11:48:36
- Clicks: 59
Abstract: The extrusion die casting process was adopted to develop the 400MPa automotive steering knuckle die casting. Aluminum alloy steering knuckle die castings with high strength are successfully...
Die Casting Technologies of Automobile Structural Parts (Part Three)
- Posted: 12/16/2020 17:46:55
- Edited: 12/16/2020 18:15:55
- Clicks: 40
3.6 The vacuum process Vacuum filling is an important process measure for die casting of automobile structural parts. The following aspects should be paid attention to when using vacuum process: (1) Start...
The Die Casting Technology of Automobile Structural Parts (Part Two)
- Posted: 12/01/2020 16:02:13
- Edited: 12/16/2020 18:15:36
- Clicks: 49
3.3 Alloy melting and processing For general use, Silafont-36 and Castasil-37 alloys can be used in die casting production without special treatments. However, if you need to produce die castings with...
The Die Casting Technology of Automobile Structural Parts (Part One)
- Posted: 11/04/2020 13:00:30
- Edited: 12/16/2020 18:14:55
- Clicks: 150
Introduction Due to high performance and quality requirements, most automobile structural parts are made of iron or steel materials and produced through other manufacturing processes. With the...
How to Prevent Mold Sticking?
- Posted: 10/30/2023 11:22:51
- Edited: 10/30/2023 11:38:19
- Clicks: 7
In the past two years, with the development of the die-cast industry, die-cast simulation (commonly known as mold flow analysis) has gradually been widely accepted and applied, and its practical role...
Test Results & Analysis of Properties of ADC12 Aluminum Alloys (Part Two)
- Posted: 08/30/2023 11:25:59
- Edited: 08/30/2023 11:52:48
- Clicks: 7
2.3 Analysis of intermetallic compounds Figure 8 SEM images of intermetallic compounds in the alloy Figure 8 is the SEM image of the intermetallic compound in the alloy. It...
News
Contact
Latest News
Technical Articles
-
How to Prevent Mold Sticking?
10 30, 2023
Useful Links
Copyright © 2014-2024 China Topper Die Casting Company Limited. All Rights Reserved. Privacy Policy | Terms of Service | Sitemap
Links: Die Casting, Linear Robot Arm for Die Casting Machine.
Website Design & Support: jeawin.com